Check out Glinski's Hexagonal Chess, our featured variant for May, 2024.

Enter Your Reply

The Comment You're Replying To
Derek Nalls wrote on Wed, Apr 30, 2008 10:47 PM EDT:
As far as playtesting goes ...

Admittedly, my initial intention was just to amuse myself by 
disproving the consistency of Muller's unusually-high archbishop 
material value in relation to other piece values within his CRC set.
If indeed his archbishop material value had been as fictitious as it 
was radical, then this would have been readily-achievable 
using any high-quality chess variant program such as SMIRF.
No matter what test I threw at it, this never happened.

Previously, I have only used 'symmetrical playtesting'.
By this I mean that the material and positions of the pieces
of both players have been identical relative to one another.
This is effective when playing one entire set of CRC piece values
against another entire set as, for example, Reinhard Scharnagl & I
have done on numerous occasions.  The player that consistently 
wins all deep-ply (long time per move) games, alternatively playing 
white and black, can be safely concluded to be the player using 
the better of the two sets of CRC piece values since this single 
variable has been effectively isolated.  However, this playtesting
method cannot isolate which individual pieces within the set 
carry the most or least accurate material values.

In fact, I had no problem with Muller's set of CRC piece values
as a whole.  The order of the material values of all of the CRC 
pieces was-is correct.  However, I had a large problem with his
material value for the archbishop being nearly as high as for
the chancellor.  

To pinpoint an unreasonably-high material value for only one 
piece within a CRC set required 'asymmetrical playtesting'.  
By this I mean that the material and positions of the pieces 
of both players had to be different in an appropriate manner to
test the upper and lower limits of the material value for a certain 
piece (e.g., archbishop).  This was achieved by removing select
pieces from both players within the Embassy Chess setup so that 
BOTH players had a significant material advantage consistent
with different models (i.e., Scharnagl set vs. Muller set).  
This was possible strictly because of the sharp contrast between the 
'normal, average' and 'very high', respectively, material values 
for the archbishop assigned by Scharnagl and Muller.  The fact
that the SMIRF program implicitly uses the Scharnagl set to play
both players is a control variable- not a problem- since it is 
insures equality in the playing strength with which both players
are handled.  The player using the Scharnagl set lost every game 
using SMIRF MS-173h-X ... regardless of time controls, 
white or black player choice and all variations in excluded pieces 
that I could devise.

I thought it was remotely possible that an intransigent, positional 
advantage for the Muller set somehow happened to exist within the 
modified Embassy Chess setup that was larger than its material 
disadvantage.  This type of catastrophe can be the curse of 
'asymmetrical playtesting'.  So, I experimented likewise using a 
few other CRC variants.  Same result!  The Scharnagl set lost every 
game.

I seriously doubt that all CRC variants (or at least, the games I tested)
are realistically likely to carry an intransigent, positional advantage 
for the Muller set.  If this is true, then the Muller set is provably, 
ideally suited to CRC, notwithstanding- just for a different reason.

Finally, I reconsidered my position and revised my model.

Edit Form
Conduct Guidelines
This is a Chess variants website, not a general forum.
Please limit your comments to Chess variants or the operation of this site.
Keep this website a safe space for Chess variant hobbyists of all stripes.
Because we want people to feel comfortable here no matter what their political or religious beliefs might be, we ask you to avoid discussing politics, religion, or other controversial subjects here. No matter how passionately you feel about any of these subjects, just take it someplace else.
Quick Markdown Guide

By default, new comments may be entered as Markdown, simple markup syntax designed to be readable and not look like markup. Comments stored as Markdown will be converted to HTML by Parsedown before displaying them. This follows the Github Flavored Markdown Spec with support for Markdown Extra. For a good overview of Markdown in general, check out the Markdown Guide. Here is a quick comparison of some commonly used Markdown with the rendered result:

Top level header: <H1>

Block quote

Second paragraph in block quote

First Paragraph of response. Italics, bold, and bold italics.

Second Paragraph after blank line. Here is some HTML code mixed in with the Markdown, and here is the same <U>HTML code</U> enclosed by backticks.

Secondary Header: <H2>

  • Unordered list item
  • Second unordered list item
  • New unordered list
    • Nested list item

Third Level header <H3>

  1. An ordered list item.
  2. A second ordered list item with the same number.
  3. A third ordered list item.
Here is some preformatted text.
  This line begins with some indentation.
    This begins with even more indentation.
And this line has no indentation.

Alt text for a graphic image

A definition list
A list of terms, each with one or more definitions following it.
An HTML construct using the tags <DL>, <DT> and <DD>.
A term
Its definition after a colon.
A second definition.
A third definition.
Another term following a blank line
The definition of that term.